# Robust clay binder for earth-based concrete

- **DOI:** [10.1016/j.cemconres.2023.107207](https://doi.org/10.1016/j.cemconres.2023.107207)
- **Rating:** Sound (3.2 out of 5)
- **Verdict:** Cross-clay testing links binder rheology and strength to accessible measurements, but laboratory micromortars do not establish general prediction for earth concrete.
- **Framework version:** v5.10
- **Pipeline version:** v0.4
- **Evaluation date:** 2026-10-21
- **Evaluation page:** https://www.nabu.science/paper/10.1016%2Fj.cemconres.2023.107207

## Key claims

1. We show that the solid volume fraction of clay paste is the key parameter allowing predicting the fresh state properties of the clay binder, whatever the constitutive clay type
   - Support: Tentative
   - Type: Primary finding
   - Basis: nine-clay laboratory evidence shows mineralogy-dependent divergence below 0.75 ϕ/ϕm
   - Location: Abstract
2. the clay activity and the dry density of the material control the compressive strength of the material
   - Support: Tentative
   - Type: Secondary
   - Basis: correlations across oven-dried micromortars do not identify causal control independently of mineralogy
   - Location: Abstract
3. YODEL model is able to predict the yield stress of all tested clays with the same pre-factor m1 value and microstructure descriptions parameters only related to the liquid limit values
   - Support: Tentative
   - Type: Secondary
   - Basis: partly fitted predictions require clay-group-specific percolation thresholds rather than liquid limit alone
   - Location: Section 4.2
4. key parameters allowing mastering the variability of the earth are the binder's activity, determined through the MBV, and the dry density of the material.
   - Support: Tentative
   - Type: Secondary
   - Basis: qualitative validation on nine fine-fraction sludges does not establish control of whole-earth variability
   - Location: Section 4.4

## Strengths

- **Material coverage spans three clay groups** Nine characterised clays cover kaolinite, illite, and smectite groups, with nine quarry sludges providing an additional material comparison.
  - Dimension: methodological rigour
  - Location: §§2.1–2.3; Tables 1–3; §4.4
- **Complementary methods support fresh state measurements** Fall-cone and vane-rheometer protocols examine yield stress across different consistency ranges, reducing reliance on a single measurement method.
  - Dimension: methodological rigour
  - Location: §3.2; §4.2; Figs. 2–3
- **Accessible measurements organise clay binder behaviour** Liquid-limit normalisation and the density–methylene-blue framework extend prior kaolinite work toward a broader, material-scale mix-design approach.
  - Dimension: contribution
  - Location: Introduction; §§4.2–4.3; Figs. 3–6

## Limitations

- **Predictive performance lacks quantified error estimates** The principal relationships are assessed graphically without reported numerical fit uncertainty or residual analysis. Partly calibrated YODEL parameters and unclear preparation independence further limit assessment of predictive performance.
  - Dimension: methodological rigour
  - Location: §3.3; §§4.2–4.4; Figs. 4–7
- **Headline universality exceeds the demonstrated regime** The abstract's clay-independent fresh-state claim overlooks divergence below 0.75 ϕ/ϕm. Section 4.2 identifies this lower-yield-stress range as relevant to poured and self-compacting earth.
  - Dimension: reporting
  - Location: Abstract; §4.2
- **Laboratory validation stops short of construction** The strength evidence comes from micromortars dried at 105 °C, while the sludge comparison remains qualitative. Performance of full earth concrete under service conditions is not established.
  - Dimension: application pathway
  - Location: §3.3; §4.4; Conclusion

## Reliability checks

Caveats (4 of 4 checks).

- **Results check:** Noted
  - YODEL model is able to predict the yield stress of all tested clays with the same pre-factor m1 value and microstructure descriptions parameters only related to the liquid limit values: "By applying the relationship ϕm = ϕLL/0.86" (Section 4.2) vs "m1=1.5 Pa; ϕm = 0.86ϕLL" (Fig. 4 caption). The two definitions of ϕm differ by a factor of 1/0.86² ≈ 1.352 and therefore imply different ϕ/ϕm normalisations. → Effect on result unclear
- **Reporting and transparency:** Noted. The data-availability statement conflicts with the experimental measurements reported in the methods. The sludge application also points to the wrong section for the hardened-state correlation.
  - Conflict of interest: declared · Data availability: not stated
- **Reference integrity:** Clean
  - 84 references in manuscript
  - 65 of 65 checkable references found in an index
  - 19 have no canonical index record — counted, but not index-checkable
  - 4 references confirmed by manual review
  - Citation details diverge for 2 references:
    - #48 [Author], [Author], [Author], Influence of additives on poured earth strength development, Mater. Struct. Constr. 53 (2020) 1–17, https://doi.org/10.1617/ s11527-020-01564-y. (DOI resolves to: “Influence of additives on poured earth strength development” — Ardant, 2020 (Materials and Structures). Differs from the DOI’s record on: container, authors) https://doi.org/10.1617/s11527-020-01564-y
    - #78 A. Mesbah, J.C. Morel, M. Olivier, Clayey soil behaviour under static compaction test, Mater. Struct. Constr. 32 (1999) 687–694, https://doi.org/10.1007/ bf02481707. (DOI resolves to: “Comportement des sols fins argileux pendant un essai de compactage statique: détermination des paramètres pertinents” — Mesbah, 1999 (Materials and Structures). Differs from the DOI’s record on: container, title) https://doi.org/10.1007/bf02481707
  - References not verified automatically are resolved manually within 24 hours.

## Post-publication record

- **Status:** Clean
- **Summary:** No retraction or expression of concern found in Crossref (includes Retraction Watch).
- **Last checked:** 2026-10-21
